找東莞走刀式分板機廠家，推薦東莞市宇順力自動化設備有限公司，公司主營 激光分板機、PCB分板機、鋁基板分板機、LED燈帶分板機、多刀分板機、走刀分板機、分板機、鍘刀分板機、沖床分板機、銑刀分板機、橫豎方向分板機、郵票孔分板機、在線鑼板機、離線鑼板機、曲線分板機、FR4分板機、FPC分板機等，歡迎電話咨詢
走刀式分板機通電通氣的狀態下,踩下腳踏開關,上刀壓下時, 此時松開手滑閥,然后再松開腳踏開關, 使上刀停在底部. 用4mm 六角匙調節捌個無頭螺絲, 調到下刀與上刀平行,確定平行后鎖緊5個壓刀螺釘。
Under the condition of power supply and ventilation, step on the foot switch. When the upper knife is pressed down, release the hand slide valve, and then release the foot switch to stop the upper knife at the bottom. Use a 4mm hexagon key to adjust eight headless screws until the lower cutter is parallel to the upper one, and then lock the five knife pressing screws.
在分切普遍的基板時,中的上下刀A,B兩平面位于同一平面.若分切韌性較強的產品.可將上圖中的4個螺絲C松開.將下刀及其刀架同時向左調節,調節范圍不宜超過0.1MM.爾后將下刀上調0.10—0.20MM,使上下切刀產生一定的交叉.從而將產品分切開(調節過程中要踩著腳踏,防止調節過量從而造成上下切刀的崩裂)調節之后將螺釘C鎖緊。新機器在分切一段時間之后,可能會出現分不開的情況,可先踩著腳踏開關,將的八個無頭螺釘均勻向下頂,使下刀上升.單次調節量不超過0.1MM為宜.防止上下刀相撞。
When cutting common substrates, the upper and lower blades a and B are located on the same plane. For products with strong cutting toughness, loosen the four screws C in the figure above. Adjust the lower cutter and its holder to the left at the same time, and the adjustment range should not exceed 0.1 mm. Then, adjust the lower knife by 0.10-0.20 mm to make the upper and lower cutters intersect to a certain extent, After adjustment, screw C is locked. After the new machine is cut for a period of time, it may not be separated. Step on the foot switch and push the eight headless screws down evenly to make the lower knife rise. The single adjustment should not exceed 0.1 mm to prevent the upper and lower knives from colliding.
想了解更多關于走刀分板機 多刀分板機 離線鑼板機信息推薦我們的網站：www.e4244.cn